Cisco (010-151-DCTECH) Exam Questions And Answers page 1
Which three steps do you perform to troubleshoot when a rack server powers on with no video? (Choose three.)
Check the front I/O cable connection to the motherboard.
Check for memory subsystem failure.
Verify the power source to equipment.
Reseat the DIMMs, CPU, and PCI cards.
Data Center Compute Resources
Data Center Automation and Orchestration
Which two statements are true about system controllers of Cisco Nexus 9500 Series? (Choose two.)
They provide centralized arbitration to the system fabric for all line cards.
They control the Layer 2 and Layer 3 services.
The Cisco Nexus 9500 Series switch software, Enhanced NX-OS, runs on the system controllers.
They are used to offload the internal non-data-path switching and management functions from the supervisor engines.
The Cisco Nexus 9500 Series supports redundant system controllers.
Cisco Data Center Devices
Data Center Networking
What does item A represent in the exhibit?
Single Choice
Refer to the exhibit.
Which item does A represent?
Which item does A represent?
Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers
Virtual Interface Card for Cisco UCS B420 M3 Blade Servers
mLOM for Cisco UCS B420 M3 Blade Servers
Virtual Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers
SuperCap module for Cisco UCS B420 M3 Blade Servers
Data Center Fundamentals
Cisco Data Center Devices
Which method does FCIP use to enable connectivity of geographically distributed Fibre Channel SANs over IP?
routing
tunneling
handshaking
transporting
Data Center Fundamentals
Data Center Networking
Refer to the exhibit. Which two faults can occur if the System Health LED is in a steady amber state? (Choose two.)
At least one DIMM is faulty.
Major fault with CPU
Major fault with the system board
CPU mismatch
Major fault with memory DIMM
Data Center System Devices
Data Center Automation and Orchestration
What is the maximum distance that the 40GBASE-LR4 Ethernet standard can span?
550 m
10 km
40 km
80 km
Data Center Compute Connectivity
Data Center Networking
Which three troubleshooting procedures do you perform when there is no power to a Cisco UCS B250 M2 Blade Server? (Choose three.)
Decommission and acknowledge the blade.
Check the back of the blade to ensure that there is no damage to the connection that goes into chassis.
Reseat the memory DIMMs.
Check the CPU sockets for bent pins.
Reseat the blade in the same slot in the chassis.
Move the blade to another slot in the chassis.
Data Center Compute Resources
Cisco Data Center Devices
What are two common steps to troubleshooting a rack server with unrecognized or memory errors? (Choose two.)
Ensure DIMMs are installed in correct slots
Check CPU sockets for bent pins
Check that the AC power cord is OK
Reseat DIMMs
Check the front I/O cable connection to the motherboard
Data Center System Devices
Data Center Compute Resources
Which Cisco Nexus 5000 Series model supports 1/10G BASE-T ports?
Cisco Nexus 5548P
Cisco Nexus 5548UP
Cisco Nexus 5596UP
Cisco Nexus 5596T
Cisco Data Center Devices
Data Center Networking
What does item A represent in the exhibit?
Single Choice
Refer to the exhibit.
Which item does A represent?
Which item does A represent?
Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers
Virtual Interface Card for Cisco UCS B420 M3 Blade Servers
mLOM for Cisco UCS B420 M3 Blade Servers
Virtual Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers
SuperCap module for Cisco UCS B420 M3 Blade Servers
Data Center Fundamentals
Cisco Data Center Devices
Comments