Cisco (200-301) Exam Questions And Answers page 79
Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?
Spanning-tree will need to be used.
The router will not accept the addressing scheme.
The connection between switches should be a trunk.
The router interfaces must be encapsulated with the 802.1Q protocol.
Network Access
IP Connectivity
What cable connects a router to a switch?
Single Choice
Which of the following cables would be used to connect a router to a switch?
v.35
crossover
rollover
straight-through
Network Access
IP Connectivity
Which Cisco IOS command is used to configure encapsulation for a PPP serial link on a Cisco router?
encapsulation ppp
encapsulation ip ppp
ip encapsulation ppp
encapsulation ppp-synch
Network Access
IP Services
Which prompt indicates the configuration mode at which Cisco IOS debug commands can be issued?
router>
router#
router(config)#
router(config-if)#
Network Access
IP Services
Which Cisco IOS command will indicate that interface GigabitEthernet 0/0 is configured via DHCP?
show ip interface GigabitEthernet 0/0 dhcp
show interface GigabitEthernet 0/0
show ip interface dhcp
show ip interface GigabitEthernet 0/0
show ip interface GigabitEthernet 0/0 brief
Network Access
IP Connectivity
In the diagram below, when a packet sent from the PC at 10.0.1.3 to the PC at 10.1.1.3 leaves the Fa0/1 interface of R1, what will be the source and destination IP and MAC addresses?
source IP 10.1.1.2 destination IP 10.1.1.3
Source MAC ad.ad.ad.ad.ad.ad destination MAC ab.ab.ab.ab.ab.ab
Source MAC ad.ad.ad.ad.ad.ad destination MAC ab.ab.ab.ab.ab.ab
source IP 10.1.1.1 destination IP 10.1.1.3
Source MAC ad.dd.dd.dd.dd.dd.dd destination MAC ab.ab.ab.ab.ab.ab
Source MAC ad.dd.dd.dd.dd.dd.dd destination MAC ab.ab.ab.ab.ab.ab
source IP 10.0.1.3 destination IP 10.1.1.3
Source MAC ad.ad.ad.ad.ad.ad destination MAC ae.ae.ae.ae.ae.ae
Source MAC ad.ad.ad.ad.ad.ad destination MAC ae.ae.ae.ae.ae.ae
source IP 10.0.6.3 destination IP 10.1.1.3
Source MAC ad.ad.ad.ad.ad.ad destination MAC ae.ae.ae.ae.ae.ae
Source MAC ad.ad.ad.ad.ad.ad destination MAC ae.ae.ae.ae.ae.ae
Network Access
IP Connectivity
An engineer must configure interswitch VLAN communication between a Cisco switch and a third-party switch. Which action should be taken?
configure DSCP
configure IEEE 802.1q
configure ISL
configure IEEE 802.1p
Network Access
IP Connectivity
You run the following command:
switch# show ip interface brief
What information is displayed?
switch# show ip interface brief
What information is displayed?
A summary of the IP addresses and subnet mask on the interface
A summary of the IP addresses on the interface and the interface's status
The IP packet statistics for the interfaces
The IP addresses for the interface and the routing protocol advertising the network
IP Connectivity
IP Services
How many IP addresses can be assigned to hosts in subnet 192.168.12.64/26?
32
62
128
256
IP Connectivity
IP Services
An engineer configures interface Gi1/0 on the company PE router to connect to an ISP. Neighbor discovery is disabled.
Which action is necessary to complete the configuration if the ISP uses third-party network devices?
Which action is necessary to complete the configuration if the ISP uses third-party network devices?
Disable autonegotiation.
Enable LLDP globally.
Enable LLDP-MED on the ISP device.
Disable Cisco Discovery Protocol on the interface.
Network Access
IP Connectivity
Comments