Troubleshooting Cisco Data Center Infrastructure 300-615-DCIT

Cisco (300-615-DCIT) Exam Questions And Answers page 12

How to resolve the error "Cannot configure postcard when inband-telemetry is configured" on Cisco Nexus 9000 Series Switch?

Single Choice

An engineer enables the packet postcards feature on a Cisco Nexus 9000 Series Switch but receives this error message:

Error: Cannot configure postcard when inband-telemetry is configured.

Which action resolves the issue?

Disable the hardware-telemetry feature.

Disable the telemetry feature.

Disable the software-telemetry feature.

Disable the inband-telemetry feature.

Data Center Infrastructure Troubleshooting Data Center Network Services Troubleshooting

What commands are needed to configure HSRP on a Nexus 7000 switch for VLAN 100?

Single Choice

An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional, the router must be the active master. Which set of commands must be used to implement the scenario?

feature hsrp
interface vlan100
ip address 10.1.1.2 255.255.255.0
priority 255
preempt
hsrp version 2
hsrp 1000
ip 10.1.1.1

feature-set hsrp
interface vlan100
ip address 10.1.1.2 255.255.255.0
priority 20
preempt
hsrp version 2
hsrp 1000
ip 10.1.1.1

feature-set hsrp
interface vlan100
ip address 10.1.1.2 255.255.255.0
priority 80
preempt
hsrp version 2
hsrp 1000
ip 10.1.1.1

feature hsrp
interface vlan100
ip address 10.1.1.2 255.255.255.0
priority 240
preempt
hsrp version 2
hsrp 1000
ip 10.1.1.1

Data Center Infrastructure Troubleshooting Data Center Network Services Troubleshooting

What are the two SPAN characteristics that must be considered when configuring SPAN on a Cisco Nexus 5000 Series Switch for packet analysis?

Multiple Choice

The engineer must configure SPAN on a Cisco Nexus 5000 Series Switch to get a capture of the traffic from these applications for an in-depth packet analysis.

Which two SPAN characteristics must be considered? (Choose two.)

SPAN source ports can be monitored in multiple SPAN sessions.

The Ethernet, FC, vFC, port channel, SAN port channel can be used as SPAN source ports.

A SPAN source port cannot be a destination SPAN port.

Only Ethernet, FC, vFC, port channel port types can be used as SPAN source ports.

The rx/tx option is available for VLAN or VSAN SPAN sessions.

Data Center Infrastructure Troubleshooting Data Center Network Services Troubleshooting

How to resolve a vPC Type-1 inconsistency in a VXLAN EVPN setup?

Multiple Choice

A vPC Type-1 inconsistency between two vPC peers in a VXLAN EVPN setup is discovered. Which two actions need to be attempted to resolve the issue? (Choose two.)

Configure the NVE interfaces to be Up on both switches.

Set a different distributed gateway virtual MAC address.

Set a different secondary IP addresses on NVE source-interface.

Configure the same VNI to multicast group maping.

Set a different primary IP addresses on NVE source-interface.

Data Center Troubleshooting Methodologies Data Center Network Services Troubleshooting

What considerations must be made when enabling port security on a Cisco MDS 9000 Series Switch?

Single Choice

An engineer is enabling port security on a Cisco MDS 9000 Series Switch.

Which feature of enabling port security on a Cisco MDS 9000 Series Switch must be considered?

It is distributed by using Cisco Fabric Services.

It authorizes only the configured sWWN to participate in the fabric.

It always learns about switches that are logging in.

It binds the fabric at the switch level.

Data Center Infrastructure Troubleshooting Data Center Network Services Troubleshooting

What are the two commands needed to complete the configuration for service degradation on a VM deployed on a Cisco UCS blade server?

Multiple Choice

Refer to the exhibit. Service degradation is reported on a VM that is deployed on a Cisco UCS blade server. The traffic from the vNIC is required to SPAN in both directions to a packet analyzer that is connected to UCS-A slot 2 port 12. Which two commands are needed to complete the configuration? (Choose two.)

UCS-A /org/service-profile/vnic/mon-src* # set direction receive transmit

UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create dest-interface 2 12

UCS-A /eth-traffic-mon/fabric/eth-mon-session # activate

UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create eth-mon-session/dest-interface 2 12

UCS-A /org/service-profile/vnic/mon-src* # set direction both

Data Center Infrastructure Troubleshooting Data Center Infrastructure Troubleshooting

What server maintenance action resolves the "resolve slot" warning after replacing a failed memory on a Cisco UCS B-Series Blade Server?

Single Choice

An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a resolve slot warning. Which server maintenance action resolves the issue?

Perform diagnostic interrupt on the server.

Re-acknowlegement the server.

Reset the server.

Decomission the server.

Data Center Infrastructure Troubleshooting Data Center Infrastructure Troubleshooting

What is the purpose of creating the system-fm-vrrp checkpoint?

Single Choice

Refer to the exhibit.

What is the reason the system-fm-vrrp checkpoint was created?

The VRRP process crashed and the checkpoint was automatically created.

The VRRP service restarted and the checkpoint was automatically created.

The network administrator manually created it.

The VRRP-enabled feature has been disabled.

Data Center Infrastructure Troubleshooting Data Center Network Services Troubleshooting

What is the recommended design choice for multipathing iSCSI traffic in a topology?

Single Choice

What is a recommended design choice in a topology for multipathing iSCSI traffic?

single initiator to dual targets

two NICs bonded together on the initiator

dual initiators to a single target with bonded interfaces

initiators and targets in separate subnets

Data Center Infrastructure Troubleshooting Data Center Network Services Troubleshooting

What is the default virtual MAC address for HSRP version 2 group 10?

Single Choice

Which virtual MAC address is the default for HSRP version 2 group 10?

0000.5E00.0110

0000.0C9F.F00A

3784.0898.1C0A

0000.0C9F.F010

Data Center Infrastructure Troubleshooting Data Center Network Services Troubleshooting

Previous Questions

Next Questions

Cisco (300-615-DCIT) Exam Questions And Answers page 12

How to resolve the error "Cannot configure postcard when inband-telemetry is configured" on Cisco Nexus 9000 Series Switch?

Correct Answer:

References:

Comments

What commands are needed to configure HSRP on a Nexus 7000 switch for VLAN 100?

Correct Answer:

References:

Comments

What are the two SPAN characteristics that must be considered when configuring SPAN on a Cisco Nexus 5000 Series Switch for packet analysis?

Comments

How to resolve a vPC Type-1 inconsistency in a VXLAN EVPN setup?

Comments

What considerations must be made when enabling port security on a Cisco MDS 9000 Series Switch?

Comments

What are the two commands needed to complete the configuration for service degradation on a VM deployed on a Cisco UCS blade server?

Correct Answers:

References:

Comments

What server maintenance action resolves the "resolve slot" warning after replacing a failed memory on a Cisco UCS B-Series Blade Server?

Comments

What is the purpose of creating the system-fm-vrrp checkpoint?

Comments

What is the recommended design choice for multipathing iSCSI traffic in a topology?

Comments

What is the default virtual MAC address for HSRP version 2 group 10?

Comments

{{ exam.shortName }}

{{ exam.longName }}