Cisco (350-401-ENCOR) Exam Questions And Answers page 17
Drag and drop the descriptions from the left onto the routing protocol they describe on the right.
Infrastructure
Network Assurance
You issue the show runningconfig command on RouterA and receive the following partial output:
Ho much web traffic can RouterA send out the FastEthernet0/1 interface during periods of heavy voice and video traffic? (Select the best answer.)
Ho much web traffic can RouterA send out the FastEthernet0/1 interface during periods of heavy voice and video traffic? (Select the best answer.)
15 Mbps
20 Mbps
25 Mbps
40 Mbps
Infrastructure
Network Assurance
A client device fails to see the enterprise SSID, but other client devices are connected to it.
What is the cause of this issue?
What is the cause of this issue?
The client has incorrect credentials stored for the configured broadcast SSID.
The hidden SSID was not manually configured on the client.
The broadcast SSID was not manually configured on the client.
The client has incorrect credentials stored for the configured hidden SSID.
Infrastructure
Network Assurance
What is the data policy in Cisco SD-WAN deployment?
Single Choice
What is the data policy in a Cisco SD-WAN deployment?
list of ordered statements that define node configurations and authentication used within the SD-WAN overlay
set of statements that defines how data is forwarded based on IP packet information and specific VPNs
detailed database mapping several kinds of addresses with their corresponding location
group of services tested to guarantee devices and links liveliness within the SD-WAN overlay
Infrastructure
Network Assurance
Which LISP infrastructure device provides connectivity between non-LISP sites and LISP sites by receiving non-LISP traffic with a LISP site destination?
PITR
map resolver
map server
PETR
Infrastructure
Network Assurance
Which measure is used by an NTP server to indicate its closeness to the authoritative time source?
stratum
time zone
latency
hop count
Network Assurance
Security
You are configuring 802.1X authentication on the FastEthernet 0/1 port on a switch named SwitchA. You want to ensure that any hosts connected to the port are authenticated by using 802.1X before the hosts can transmit data through the switch.
Which of the following command sequences should you issue on SwitchA? (Select the best answer.)
Which of the following command sequences should you issue on SwitchA? (Select the best answer.)
SwitchA#configure terminalSwitchA(config)#aaa newmodel
SwitchA(config)#aaa authentication dot1x default group radius
SwitchA(config)#dot1x systemauthcontrol
SwitchA(config)#interface fastethernet 0/1
SwitchA(configif)#dot1x portcontrol forceauthorized
SwitchA(config)#aaa authentication dot1x default group radius
SwitchA(config)#dot1x systemauthcontrol
SwitchA(config)#interface fastethernet 0/1
SwitchA(configif)#dot1x portcontrol forceauthorized
SwitchA#configure terminalSwitchA(config)#aaa newmodel
SwitchA(config)#aaa authentication dot1x default group radius
SwitchA(config)#dot1x systemauthcontrol
SwitchA(config)#interface fastethernet 0/1
SwitchA(configif)#dot1x portcontrol forceunauthorized
SwitchA(config)#aaa authentication dot1x default group radius
SwitchA(config)#dot1x systemauthcontrol
SwitchA(config)#interface fastethernet 0/1
SwitchA(configif)#dot1x portcontrol forceunauthorized
SwitchA#configure terminalSwitchA(config)#aaa newmodel
SwitchA(config)#aaa authentication dot1x default group radius
SwitchA(config)#dot1x systemauthcontrol
SwitchA(config)#interface fastethernet 0/1
SwitchA(configif)#dot1x portcontrol auto
SwitchA(config)#aaa authentication dot1x default group radius
SwitchA(config)#dot1x systemauthcontrol
SwitchA(config)#interface fastethernet 0/1
SwitchA(configif)#dot1x portcontrol auto
SwitchA#configure terminalSwitchA(config)#aaa newmodel
SwitchA(config)#aaa authentication dot1x default group radius
SwitchA(config)#dot1x systemauthcontrol
SwitchA(config)#interface fastethernet 0/1
SwitchA(configif)#dot1x portcontrol all
SwitchA(config)#aaa authentication dot1x default group radius
SwitchA(config)#dot1x systemauthcontrol
SwitchA(config)#interface fastethernet 0/1
SwitchA(configif)#dot1x portcontrol all
Network Assurance
Security
Which of the following ICMPv6 message types is sent by an IPv6capable host at startup? (Select the best answer.)
router solicitation
router advertisement
neighbor solicitation
neighbor advertisement
Virtualization
Network Assurance
Refer to the exhibit.
Assuming the WLC's interfaces are not in the same subnet as the RADIUS server, which interface would the WLC use as the source for all RADIUS-related traffic?
Assuming the WLC's interfaces are not in the same subnet as the RADIUS server, which interface would the WLC use as the source for all RADIUS-related traffic?
the controller management interface
the controller virtual interface
the interface specified on the WLAN configuration
any interface configured on the WLC
Infrastructure
Security
Refer to the exhibit.
The EtherChannel between SW2 and SW3 is not operational. Which action resolves this issue?
The EtherChannel between SW2 and SW3 is not operational. Which action resolves this issue?
Configure the channel-group mode on SW3 Gi0/0 and Gi0/1 to active.
Configure the mode on SW2 Gi0/0 to trunk.
Configure the channel-group mode on SW2 Gi0/0 and Gi0/1 to on.
Configure the mode on SW2 Gi0/1 to access.
Infrastructure
Network Assurance
Comments