Implementing and Operating Cisco Enterprise Network Core Technologies 350-401-ENCOR

Cisco (350-401-ENCOR) Exam Questions And Answers page 37

What does the IPsec VPN show command display for the ISAKMP SA status?

Single Choice

Refer to the exhibit. After configuring an IPsec VPN, an engineer enters the show command to verify the ISAKMP SA status. What does the status show?

VPN peers agreed on parameters for the ISAKMP SA.

Peers have exchanged keys, but ISAKMP SA remains unauthenticated.

ISAKMP SA is authenticated and can be used for Quick Mode.

ISAKMP SA has been created, but it has not continued to form.

Virtualization Security

What does the output of the show command confirm for the NAT configuration on R1?

Single Choice

Refer to the exhibit. A network engineer configures NAT on R1 and enters the show command to verify the configuration. What does the output confirm?

The first packet triggered NAT to add an entry to the NAT table.

R1 is configured with NAT overload parameters.

A Telnet session from 160.1.1.1 to 10.1.1.10 has been initiated.

R1 is configured with PAT overload parameters.

Virtualization Infrastructure

When is an outbound QoS policy on a router WAN interface most beneficial for network conditions?

Single Choice

Under which network conditions is an outbound QoS policy that is applied on a router WAN interface most beneficial?

under traffic classification and marking conditions

under interface saturation conditions

under all network conditions

under network convergence conditions

Infrastructure Network Assurance

What command set must be applied to resolve the communication issue between London and New York?

Single Choice

Refer to the exhibit. Communication between London and New York is down. Which command set must be applied to resolve this issue?

NewYork(config)#int f0/1
NewYork(config)#switchport nonegotiate
NewYork(config)#end
NewYork#

NewYork(config)#int f0/1
NewYork(config)#switchport mode trunk
NewYork(config)#end
NewYork#

NewYork(config)#int f0/1
NewYork(config)#switchport trunk encap dot1q
NewYork(config)#end
NewYork#

NewYork(config)#int f0/1
NewYork(config)#switchport mode dynamic desirable
NewYork(config)#end
NewYork#

Infrastructure Network Assurance

Where does BGP PIC store an alternate path?

Single Choice

In which of the following locations does BGP PIC store an alternate path? (Select the best answer.)

only in the RIB

only in the FIB

only in CEF

only in the RIB and the FIB

in the RIB, in the FIB, and in CEF

Network Assurance Security

How does a fabric-enabled SSID handle 802.11 traffic?

Single Choice

How is 802.11 traffic handled in a fabric-enabled SSID?

centrally switched back to WLC where the user traffic is mapped to a VXLAN on the WLC

converted by the AP into 802.3 and encapsulated into VXLAN

centrally switched back to WLC where the user traffic is mapped to a VLAN on the WLC

converted by the AP into 802.3 and encapsulated into a VLAN

Infrastructure Network Assurance

What is a Type 1 hypervisor and how does it differ from other types?

Single Choice

What is a Type 1 hypervisor?

runs directly on a physical server and depends on a previously installed operating system

runs directly on a physical server and includes its own operating system

runs on a virtual server and depends on an already installed operating system

runs on a virtual server and includes its own operating system

Virtualization

What is the role of Link Management Protocol in a Cisco StackWise Virtual domain?

Single Choice

Which action is performed by Link Management Protocol in a Cisco StackWise Virtual domain?

It determines which switch becomes active or standby.

It determines if the hardware is compatible to form the StackWise Virtual domain.

It rejects any unidirectional link traffic forwarding.

It discovers the StackWise domain and brings up SVL interfaces.

Infrastructure Network Assurance

What is the process for selecting a new VRRP master router when the current one fails?

Single Choice

If a VRRP master router fails, which router is selected as the new master router?

router with the lowest priority

router with the highest priority

router with the highest loopback address

router with the lowest loopback address

Virtualization Network Assurance

Which commands are needed to assign an IP address of 192.168.1.1/24 to GigabitEthernet1 interface?

Multiple Choice

Refer to the exhibit. An engineer must assign an IP address of 192.168.1.1/24 to the GigabitEthernet1 interface. Which two commands must be added to the existing configuration to accomplish this task? (Choose two.)

Router(config-if)#ip address 192.168.1.1 255.255.255.0

Router(config-vrf)#address-family ipv4

Router(config-vrf)#ip address 192.168.1.1 255.255.255.0

Router(config-if)#address-family ipv4

Router(config-vrf)#address-family ipv6

Infrastructure Security

Cisco (350-401-ENCOR) Exam Questions And Answers page 37

What does the IPsec VPN show command display for the ISAKMP SA status?

Comments

What does the output of the show command confirm for the NAT configuration on R1?

Comments

When is an outbound QoS policy on a router WAN interface most beneficial for network conditions?

Comments

What command set must be applied to resolve the communication issue between London and New York?

Comments

Where does BGP PIC store an alternate path?

Correct Answer:

Explanation:

References:

Comments

How does a fabric-enabled SSID handle 802.11 traffic?

Comments

What is a Type 1 hypervisor and how does it differ from other types?

Comments

What is the role of Link Management Protocol in a Cisco StackWise Virtual domain?

Comments

What is the process for selecting a new VRRP master router when the current one fails?

Comments

Which commands are needed to assign an IP address of 192.168.1.1/24 to GigabitEthernet1 interface?

Comments

{{ exam.shortName }}

{{ exam.longName }}