Cisco (350-601-DCCOR) Exam Questions And Answers page 7
A network engineer must enable port security on all Cisco MDS Series Switches in the fabric. The requirement is to avoid the extensive manual configuration of the switch ports. Which action must be taken to meet these requirements?
Enable the auto-learning port security feature on a per-VSAN basis.
Activate CFS distribution and the auto-learning port security feature.
Activate CFS distribution and the auto-learning port security feature on a per-VSAN basis.
Network Virtualization
Security
An engineer must configure OSPF in the data center. The external routes have already been redistributed into OSPF. The network must meet these criteria:
" The data center servers must reach services in the cloud and the services behind the redistributed routes.
" The exit point toward the Internet should be propagated only when there is a dynamically learned default route from the upstream router.
Which feature is required?
" The data center servers must reach services in the cloud and the services behind the redistributed routes.
" The exit point toward the Internet should be propagated only when there is a dynamically learned default route from the upstream router.
Which feature is required?
stubby area
totally stubby area
default-information originate
default-information originate always
Data Center Infrastructure
Network Virtualization
An engineer needs to create a new user in the local user database on Cisco UCS Fabric Interconnect. The user needs permissions to change the following configuration inside UCS Manager version 3.1:
• vNIC and vHBA profiles
• Fan speed and power redundancy profile of UCS Manager
Which two roles must be assigned to a user to achieve this goal? (Choose two.)
• vNIC and vHBA profiles
• Fan speed and power redundancy profile of UCS Manager
Which two roles must be assigned to a user to achieve this goal? (Choose two.)
facility-manager
server-equipment
operations
server-profile
server-compute
Compute
Security
Which two statements describe the process of performing an EPLD upgrade on a Cisco MDS 9000 Series Switch? (Choose two.)
The upgrade is performed from the standby supervisor module.
The upgrade process disrupts only the module that is being upgraded.
The upgrade is performed on the active supervisor.
If an upgrade is interrupted, the upgrade continues after a connection is restored.
Modules must be online to be upgraded.
Storage Networking
Security
Which two configuration settings are available in the Cisco UCS Firmware Auto Sync Server policy? (Choose two.)
Immediate Action
User Notification
User Acknowledge
Delayed Action
No Action
Data Center Infrastructure
Security
Which configuration statically assigns VSAN membership to a virtual Fibre Channel interface?
switch(config-vsan-db)# vsan 100 interface vfc 31
switch(config-vsan-db)# vsan 100 fc 3/1
switch(config-vsan-db)# vsan 100 bind interface fc 3/1
switch(config-vsan-db)# vsan 100 bind interface vfc 31
Storage Networking
Security
An engineer needs to monitor ingress traffic that arrives at interface Ethernet 1/3 that belongs to a Cisco Nexus 5600 Series Switch. The traffic analyzer machine located at interface Ethernet 1/5 is already monitoring other production, and the traffic analyzer must not be impacted by the traffic captured from the interface Eth1/3. The operations team allocated a traffic budget for the new monitoring session of 1 Gbps to meet this requirement. Which set of commands configures the SPAN session?
Network Virtualization
Security
Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal?
SW3# configure terminal
SW3(config)# source interface port-channel 1 rx
SW3(config)# source interface port-channel 2 tx
SW3(config)# interface ethernet 1/4
SW3(config-if)# destination interface ethernet 1/4
SW3(config-if)# exit
SW3(config)# interface Port-channel 1-2
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# source interface port-channel 1 rx
SW3(config)# source interface port-channel 2 tx
SW3(config)# interface ethernet 1/4
SW3(config-if)# destination interface ethernet 1/4
SW3(config-if)# exit
SW3(config)# interface Port-channel 1-2
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3# configure terminal
SW3(config)# monitor session 2
SW3(config-monitor)# source interface port-channel 1 rx
SW3(config-monitor)# source interface port-channel 2 rx
SW3(config)# interface ethernet 1/4
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# monitor session 2
SW3(config-monitor)# destination interface ethernet 1/4
SW3(config)# monitor session 2
SW3(config-monitor)# source interface port-channel 1 rx
SW3(config-monitor)# source interface port-channel 2 rx
SW3(config)# interface ethernet 1/4
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# monitor session 2
SW3(config-monitor)# destination interface ethernet 1/4
SW3# configure terminal
SW3(config)# monitor session 2
SW3(config-monitor)# source interface port-channel 1 tx
SW3(config-monitor)# source interface port-channel 2 tx
SW3(config)# interface Port-channel 1
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# interface Port-channel 2
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# monitor session 2
SW3(config-monitor)# source interface port-channel 1 tx
SW3(config-monitor)# source interface port-channel 2 tx
SW3(config)# interface Port-channel 1
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# interface Port-channel 2
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3# configure terminal
SW3(config)# monitor session 2
SW3(config-monitor)# source interface port-channel 1 tx
SW3(config-monitor)# source interface port-channel 2 rx
SW3(config)# interface port-channel 1
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# interface port-channel 2
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# monitor session 2
SW3(config-monitor)# source interface port-channel 1 tx
SW3(config-monitor)# source interface port-channel 2 rx
SW3(config)# interface port-channel 1
SW3(config-if)# switchport monitor
SW3(config-if)# exit
SW3(config)# interface port-channel 2
SW3(config-if)# switchport monitor
SW3(config-if)# exit
Network Virtualization
Storage Networking
Which NFS version uses the TCP protocol and needs only one IP port to run the service?
NFSv1
NFSv2
NFSv3
NFSv4
Storage Networking
Security
Which feature must be enabled to support the use of JSON and XML encodings when a Cisco Nexus 7000 Series Switch is deployed?
Bash shell
NX-API
Open Agent Container
LLDP
Network Virtualization
Security
Comments